A WiFi connection may not always provide the same speed as a cable connection. Among the main reasons are incorrect router settings, conflicts with neighbors' access points, and the wrong choice of the location of the router. Speed ​​is also cut when using outdated hardware or older firmware versions.

How to determine that WiFi speed is being cut

Internet providers indicate in the contract the maximum possible access speed. The actual width of the throughput channel is usually lower than the declared one. At home, it is easy to check whether this is due to restrictions on the provider's side or using WiFi. To do this, connect an Ethernet cable directly to the device from which you access the Internet.

Open the Speedtest online service in any browser and click "Begin Test". The site will automatically determine the nearest server through which the speed test will be performed. The computer will exchange data with the selected server to find out the current Internet speed. Wait until the end of the operation, then remember or write down its result.

Then connect an internet cable to your router, turn it on and connect to WiFi from the same device you tested the speed on. Open the site again and repeat the measurement. If the results of the first and second tests differ significantly, the speed is cut precisely because of the use of wireless Internet.

Interference from neighbors' wireless equipment

Most often, this reason manifests itself in apartment buildings with a large number of installed WiFi access points. The wireless network can operate in one of two bands: 2.4 or 5 GHz. The first option is more common. In this case, the actual frequency can be from 2.412 to 2.484 GHz in 0.005 GHz steps, depending on the selected channel.

The 2.4 GHz band is divided into 14 segments, but not all of them may be available for legal use in a particular country. For example, in the USA only channels 1-11 are used, in Russia: 1-13, in Japan: 1-14. Selecting an incorrect value may violate the laws of the state in which the equipment is operated.

If your neighbors' access points use the same channel as your router, interference (radio wave overlay) occurs. As a result of this, the speed of the Internet over WiFi is cut. It is recommended to analyze the current frequency congestion. The most popular software tool used for this purpose is the inSSIDer utility developed by MetaGeek.

Install the program, run the executable file and click the "Start Scan" button in the upper left corner of the program window. The graph on the right will display the found WiFi networks and the channels on which they work. Find the range that contains the fewest networks with a high level of reception, and then select it in the router control panel.

Note! The width of each channel can be 20 or 40 MHz. Only channels 1, 6, and 11 do not overlap. Use one of these values ​​for the best network setup. You can also choose to automatically detect the least loaded frequencies in the router settings.

High band occupancy

In large cities, the number of available 2.4 GHz networks can be so high that changing the WiFi channel does not lead to the desired result. The data rate is cut even after selecting the freest segment of the frequency range. The optimal solution to this problem is the transition to the 5 GHz band, which has not yet received sufficient distribution.

Its use is possible on dual-band routers. Such routers create two networks at once, which have different names, encryption and authorization parameters. Client devices whose radio module supports 5 GHz operation will be able to connect to WiFi in this range. Legacy models will connect to the second network. With this scheme of work, a number of disadvantages should be taken into account, the main of which are:

1. Smaller coverage area in the presence of obstacles, due to the physical properties of radio waves of this length.
2. Lack of compatibility with older devices.
3. The high cost of dual-band equipment.

Router Issues

The main mistake made by users when organizing a home WiFi network is the wrong choice of the location of the router. It leads to poor signal reception on client devices, due to which the Internet speed is cut. You can specify the signal level by the number of marks on the WiFi icon located in the tray (lower right corner) of the Windows operating system. On mobile devices, the Internet connection status and signal strength can be checked at the top of the screen, in the notification bar.

It is recommended to install the router in the central room of the room where it will be used. This arrangement ensures a high level of WiFi reception in all rooms of the apartment or office. When installed in the corner of a room, remote rooms will not be able to connect to the wireless network or will receive Internet at low speed.

Important! The quality of communication with the router is also affected by the transmitter power, the number of installed antennas and the distance from working sources of electromagnetic radiation. To prevent Internet speed from being cut, try to install the router away from microwave ovens, refrigerators and other household appliances.

Also check the correctness of the WiFi mode selection in the router settings. It is responsible for the maximum data transfer rate and backward compatibility with older devices. For example, if "11b only" is selected, the WiFi speed will be cut to 11Mbps, while "11g only" will limit the bandwidth to 54Mbps.

You can enter the web interface of the router at the address indicated on its bottom panel. For TP-Link models, the desired parameters are selected in the “Wireless Mode -> Wireless Settings” section. The recommended values ​​if there are older models on the network are "11bgn mixed" and "11bg mixed". If all home or office devices support the 802.11n standard, check the "11n only" box.

In the Wireless Security menu, set the security type to WPA/WPA2, as using the legacy WEP method cuts WiFi speed. Change the automatic encryption type selection to Advanced Encryption Standard (AES). It provides greater network security with less impact on data transfer rates.

Click the tab with advanced wireless network settings. On TP-Link it is "Wireless Mode -> Advanced Settings". Find and activate the "WiFi Multimedia" (WMM) option. This protocol allows you to set a high priority for multimedia traffic, thereby speeding up its transmission.

In the settings of the connected devices, you must also activate this function. Open Device Manager in the Control Panel of your Windows operating system. Find your network adapter and go to its properties. On the "Advanced" tab, select the line "WMM" in the list on the left. On the right, specify the value "Enabled" or "Enabled". Save the configuration by clicking the "OK" button.

Another parameter that you should pay attention to when configuring the router is the transmitter power or "Tx Power". This value is indicated as a percentage of the maximum power of the equipment. If the hotspot is far away, set it to "100%" to improve WiFi reception.

Outdated device firmware

Manufacturers of routers and other wireless devices regularly optimize their software for maximum performance. You can download the new firmware version on the Internet, on the developer's website. The update is performed by downloading the file to the device through the admin panel. The path in the menu of routers of different brands is different:

• TP-Link: "System Tools -> Firmware Update";
• D-Link: "System -> Software Update";
• ASUS: "Administration -> Firmware Update";
• Zyxel: "System Information -> Updates";

Advice! When installing software, consider the hardware version of the router. It is indicated on the sticker or in the documentation for the device.

On client equipment (laptops, computers and other equipment connected to WiFi), you should check the versions of network drivers. Windows OS allows you to update the firmware through the control panel, in the "Device Manager" section. Open the "Network adapters" tab and select the radio module you are using. In the "Driver" section, click "Update" and select to automatically search for software on the Internet. After that, restart your computer and connect to the wireless Internet again.

Tutorial video: How and why the Internet speed is cut over WiFi

Using optional equipment

If, after fixing all the problems, the Internet speed in remote rooms continues to cut, use additional equipment to amplify the signal. It includes: external antennas for routers, high-power wireless adapters for computers, WiFi repeaters.

When choosing an antenna, consider the gain and type of connector with which it connects to the access point. Typically, manufacturers indicate a list of equipment recommended for use with certain device models. When connecting third-party antennas that have not been tested for compatibility, difficulties may arise with further warranty service.

The repeater allows you to increase coverage and get high speed Internet even at a considerable distance from the router. Due to the use of a built-in power supply, such devices have a compact size. To use them, just plug the device into a power outlet and press the “WiFi Protected Setup” (WPS) button on the case. After that, the same button must be pressed on the router itself or a quick connection must be activated via the web interface.